You must have javascript enabled to use bicyclesi.com !

G51 EBike LCD Display E-Scooter Conversion Kit 48V Electric Bike

Component part

USD $36.09

Condition : New

Free Shipping

{{variant_type_name}} :
eBay
SKU: N/A This site contains affiliate links for which we may be compensated Sporting Goods / Cycling / Bicycle Components & Parts / Electric Bicycle Components

Notify me when the price drops

We will email you if we find a lower price on this product!

Target price (USD) $

Function Description: 1、Display function Speed display, power-assisted gear display, power indication, fault indication, total mileage, single mileage, headlight display, single driving time display 2. Control, setting function power switch control, headlight switch control, 6Km/h point control, wheel diameter setting, maximum speed setting, idle Automatic sleep time setting, backlight brightness setting, voltage level setting, 3. Communication protocol: UART Display full content (full display within 1S of power on) Display content introduction 3.1 Headlight 3.2 Battery level display BATTERY 3.3 Multi-function display area Total Mileage 0D0, Single Mileage TRIP, Fault Code Error, Power WATT, Maintenance Maintain; DST T0 GO (not used yet) 3.4 Vehicle Mode POWER: Powerful mode Speed display area Maximum speed MAX, Average speed AVG Unit MPH.KM/H The meter will calculate the real speed according to the wheel diameter and signal data. 3.6 Vehicle status display area Vehicle status symbols and code meaning: : Digital voltage; : Brake alert; : Motor fault; Communication fault;: turnbuckle fault;: controller fault. 3.7 Fault generation obstacle Fault code (decimal) Fault status Remarks 0 Normal status 1 Reserved 2 Brake 3 Boost sensor malfunction (riding symbol) not realized here 4 6KM/H cruise 5 Real-time cruise 6 Ghost pool under pressure 7 Motor failure 8 Handlebar failure 9 Controller failure 10 Communication reception failure 11 Communication transmission error 12 BMS communication failure 13 Headlight fault
3.8 Settings
PO1: Brightness of backlight, level 1 is the darkest, level 3 is the brightest;
PO2: Mileage unit, O:KM;1:MILE;
PO3: Voltage level: 24V, 36V, 48V, 6OV,64V Default 36Y;
P04: hibernation time: 0, no hibernation; other numbers are hibernation time, range: 1-60; unit minutes;
P05: booster gear: 0, 3-speed mode:
1, 5-speed mode:
P06: wheel diameter: unit, inch; accuracy: 0.1 (No. 2 protocol); 5S protocol and J-LCD protocol wheel diameter
Value for the digital code to indicate: 0:16 inch, 1:18inch, 2:20inch, 3:22inch, 4:24inch, 5:26inch, 6:700c, 7:28inch
This parameter is related to the speed displayed by the meter and needs to be entered correctly;
PO7: Number of speed measuring magnets: range: 1-100;
This parameter is related to the speed displayed on the meter and needs to be input correctly;
If it is an ordinary hub motor, directly input the number of magnets;
If it is a high-speed motor, you also need to calculate the reduction ratio, input data = number of magnets × reduction ratio;
For example: motor magnet steel number 20, deceleration ratio 4.3: input data is: 86 = 20 X 4.3
P08: speed limit: range 0-100km/h, 100 means no speed limit.
The input data here indicates the maximum operating speed of the vehicle: e.g. enter 25, which means that the maximum operating speed of the vehicle will not exceed 25km/h;
The drive speed is maintained at the set value, the
Tolerance: earth 1km/h; (booster, turn handle are speed limit)
Note: The value here is based on kilometers, when the unit setting is converted from kilometers to miles, the speed value of the display interface will be automatically converted to the correct value of miles, but the data of the speed limit value set at this menu under the miles interface is not converted and is not consistent with the actual display of the mile speed limit value;
Note: The P09-P15 menus are only valid in the communication state.
P09: zero start, non-zero start setting, 0: zero start; 1: non-zero start;
P10: drive mode setting 0: power-assisted drive (decide how much power-assisted is output through the power-assisted gear, at this time the turnbuckle is invalid).
1: electric drive (driven by the turnbuckle, at this time the power-assisted gear is invalid).
2:Boost drive and electric drive coexist at the same time
P11: Boost sensitivity setting Range: 1-24;
P12: Boost start strength setting Range: 0-5;
P13: Setting of booster magnet disk type: 5, 8, 12 grains of magnets.
P14: Controller current limit value setting default 12A
Range: 1-20A
P15: Controller under-voltage value
P16:0D0 clearing setting Long press up key for 5 seconds OD0 clearing
P17:0: do not enable cruise, 1: enable cruise; auto-cruise optional (only valid for protocol No. 2)
P18: display speed proportional adjustment Range: 50%~150%, P19:0 gear enable bit, 0: with 0 gear, 1: without 0 gear
P20:0:No.2 protocol 1:5S protocol 2:J-LCD protocol 3:standby Packaging:
1*Display Our Advantages Pre-sales service 1. Provide free consultation to solve customer's confusion and provide free technical support. 2. carefully study customer needs, according to the customer's actual installation situation to provide a detailed, suitable solution environment. In-sale service 1. Try our best to meet the reasonable needs of customers. 2. 2. Keep close contact with customers during each business period. 3. Co-operate with customers in a friendly manner to meet their needs with the best quality products. After-sales service 1. train customers how to install and use the e-bikes for free. 2. Provide one year free warranty for common products. 3. perfect after-sales service to help customers solve problems in the process of using. 4. Provide regular tracking service for customers. Shipping       1. Depending on the location of the item, items will be shipped from CN stock or US stock within 1-3 business days. 2. 2. In some cases, the shipping date may be delayed due to out of stock. We will notify you by email. 3. Please leave a usable address and phone number in the shipping information. The seller is not responsible for incorrect addresses. 4. Please indicate your personal requirements such as colour, packaging etc. when making payment. 5. 5. We will not be responsible for any delays in the delivery process, including but not limited to customs postage checks, strikes, coercive measures etc. Return Policy          1. Returned items must be unused and in the same condition and original packaging as when received. 2. 2. Once a return is approved, it is the buyer's responsibility to return the product and pack it properly to prevent any damage during shipping. 3. 3. If you receive an item and are not satisfied, please contact me before returning it. Then return it within 30 days for a replacement or refund. Postage will not be refunded.

Returns Accepted for this item if it's within 30 Days

G51 EBike LCD Display E-Scooter Conversion Kit 48V Electric Bike Component part
small
See more
Price type
IN STOCK OUT STOCK